Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
Right here below yow will discover some quality help and advice related to Installing A Bathtub.
Installing a bathtub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult job. If the old tub is easily easily accessible, the job can move quickly; if you have to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and embeded in the new one. Ensure you have actually certified on your own for the job as well as fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you might require a specialist plumber to make tube links.
This article will assist you install a brand-new bathtub in your shower room if you have actually currently bought a brand-new tub and don't need to change the arrangement of your previous water supply pipelines.
Your devices and product list must consist of the following:
Planning for the Installation
First of all, the supporting structure supplied with the bath ought to be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, put the tub in the needed placement. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub till the level checks out degree.
To install faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the water and also examine all joints and brand-new pipework for leaks and tighten them if necessary. Load the tub as well as additionally inspect the overflow electrical outlet and the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bath tub ought to wait up until the tub has actually been made use of at least once as this will resolve it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The former type should be linked to the tap ends first, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to issues with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are offered in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always load the tub with water before securing, to enable the movement experienced when the tub remains in usage. The sealer can split rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our excerpt about Installing A Bathtub. Thank you so much for taking time to browse our article. Liked our blog entry? Please share it. Let others find it. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Dial, rest easy! Report this page